MAX481ECSA+
| Parameters | |
|---|---|
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
| ESD Protection | Yes |
| Receive Delay-Max | 200 ns |
| Simplex/Duplex | Half Duplex |
| Output Low Current-Max | 0.004A |
| Number of Receivers | 1 |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX481E |
| Pin Count | 8 |
| Output Voltage | 3V |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 500μA |
| Propagation Delay | 60 ns |
| Data Rate | 2.5Mbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
MAX481ECSA+ Overview
Due to the enhanced 8-SOIC (0.154, 3.90mm Width) package, this driver IC is excellent for driving common LEDs.The package of this receiver is Tube.As a Transceiver can transceiver, this part has enabled many applications to be served.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.This differential driver consumes 4.75V~5.25V for its power supplyDuring operation, this electronic part may have up to 1/1 eligible receivers/drivers.For applications where the operating temperature is 0°C~70°C, this ic receiver was designed primarily.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.In order to drive and receive signals from data, this wide receiver has 8 terminations integrated.It is packaged with 8 pinouts that are market standard for this particular transceiver.With the part number MAX481E identifying the product type, temperature, package, etc., you can search with it to see more variants.8-pin driver chip with enhanced power dissipation.This package size decreases dramatically due to optical transceiver downsizing and high-density Surface Mount mounting technologies.This ic receiver provided a 1-bit resolution capability. There is a 5V input voltage supply that can be used to operate this transceiver module.There is a subcategory called Line Driver or Receivers for this rf transceiver module.It is designed to be operated from a 5V power supply, so the module isolated transceiver will work effectively.This rf transceiver module can have?up to 1 eligible receivers on the field at once.?A voltage of 3V can be delivered by Wide receiver.
MAX481ECSA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX481ECSA+ Applications
There are a lot of Maxim Integrated MAX481ECSA+ Drivers/Receivers/Transceivers applications.
- Sensor reporting
- Point-to-point networking
- Structural bonding
- Remote controls
- Fiber optic cable connection network
- Automation systems
- Wireless access points
- Datacom networking applications
- Laser diode bonding
- Satellite communication
