MAX4821EUP
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) Exposed Pad |
| Number of Pins | 20 |
| Weight | 190.990737mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 2Ohm |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 1.739W |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Pin Count | 20 |
| Number of Outputs | 8 |
| Output Voltage | 400mV |
| Output Type | N-Channel |
| Max Output Current | 150mA |
| Power Supplies | 3.3/5V |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.3V |
| Operating Supply Current | 50μA |
| Output Configuration | Low Side |
| Output Current | 70mA |
| Turn On Delay Time | 1 μs |
| Switch Type | Relay, Solenoid Driver |
| Output Current per Channel | 70mA |
| Rise Time | 2μs |
| Fall Time (Typ) | 2 μs |
| Turn-Off Delay Time | 1 μs |
| Ratio - Input:Output | 1:8 |
| Voltage - Load | 2.3V~5.5V |
| Driver Number of Bits | 8 |
| Output Peak Current Limit-Nom | 0.07A |
| Rds On (Typ) | 2 Ω |
| Built-in Protections | TRANSIENT |
| Height | 950μm |
| Length | 6.6mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX4821EUP Overview
As a result, it is packaged in the form of a Tube.It is included in the package 20-TSSOP (0.173, 4.40mm Width) Exposed Pad.This LED driving board is mounted using the mounting type Surface Mount.The switch type of this switch is Relay, Solenoid Driver.To ensure reliable operation, the temperature should be set to -40°C~85°C TA.By default, it is set to output 8.A maximum output voltage of N-Channel volts can be achieved by this LED driver.It consists of 20 terminations in total.During operation, the 20 pins are used.Currently, there are 1 functions associated with the lighting driver.This results in the maximum output current dropping to 150mA to meet the operation criteria.Using a voltage of 3.3V allows for high efficiency.It is mounted in the way of Surface Mount.There are 20 pins in total on this board.There is 2Ohm resistance on the LED driver.This results in a 70mA output current.Self-contained in an econtainer with a capacity of Peripheral Drivers, this LED driver is self-contained.A 3.3/5V power supply is used by the part.This LED driving board can handle voltages up to 5.5VV.It is also capable of running at 2.3V volts if necessary.
MAX4821EUP Features
Supplied from 3.3V
Resistance of 2Ohm
MAX4821EUP Applications
There are a lot of Maxim Integrated MAX4821EUP Power Switches ICs applications.
- Hot Swaps
- Solid State Drivers
- Telecom and Network Systems
- PC Card Hot Swap
- Gaming
- Notebook PC
- Storage (HDDs, SSDs)
- PC Cards
- Hard Disk Drives
- Hot Swap
