MAX483CSA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX483 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 250μA |
| Data Rate | 250kbps |
| Output Characteristics | 3-STATE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
| Number of Transceivers | 1 |
| Receive Delay-Max | 2000 ns |
| Transmit Delay-Max | 2000 ns |
| Output Low Current-Max | 0.004A |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX483CSA+T Overview
Designed for common LEDs, this driver IC features an enhanced 8-SOIC (0.154, 3.90mm Width) package.Tape & Reel (TR) package is used to mount this receiver.As a Transceiver can transceiver, this part has enabled many applications to be served.A Surface Mount-type PCB or development board can be used to place this wide receiver.A power supply of 4.75V~5.25V is used by this differential driver.At any one time, this electronic part can have up to 1/1 eligible receivers/drivers.As its name implies, this ic receiver is designed for applications where 0°C~70°C is the operating temperature.An output voltage range of 5V is sufficient to run this line driver ic efficiently.The integrated terminations of this wide receiver allow it to drive and receive signals from data.Transceiver comes with 8 standard pinouts that meet the market's requirements.Since the base part number MAX483 describes the product type, temperature, package, etc., you might get more options by searching with it.An enhanced power dissipation control driver IC featuring 8 pins.Optical transceiver package size is greatly reduced due to downsizing of the ICs and high-density Surface Mount mounting technologies.In terms of resolution, this ic receiver was capable of providing a 1-bit resolution.There is usually a 1-bit resolution specified for this receiver when it is used.There are two types of input voltage supply available for this IC, 5V.A rf transceiver module named Line Driver or Receivers belongs to this subcategory.IC5V is a high performance driver IC designed to work with a 5V power supply.In total, there are 1 transceivers implemented by this module isolated transceiver.
MAX483CSA+T Features
Tape & Reel (TR) package
8 pin count
8 pins
5V power supply
MAX483CSA+T Applications
There are a lot of Maxim Integrated MAX483CSA+T Drivers/Receivers/Transceivers applications.
- Shortwave receiver
- Clock radio
- Portable radio
- Wireless projection application for conferences
- Servers
- Cable network front end
- IPTV front end
- Wireless communication
- Satellite ground stations
- Point-to-point networking
