MAX483ECSA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX483 |
| Pin Count | 8 |
| Output Voltage | 3V |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 250μA |
| Propagation Delay | 250 ns |
| Data Rate | 250kbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
| Number of Transceivers | 1 |
| Receive Delay-Max | 2000 ns |
| Simplex/Duplex | Half Duplex |
| Transmit Delay-Max | 2000 ns |
| Output Low Current-Max | 0.004A |
| High Level Input Current-Max | 0.000002A |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX483ECSA+T Overview
An excellent driver IC for common LEDs thanks to its enhanced 8-SOIC (0.154, 3.90mm Width) package.Tape & Reel (TR) package is used for this receiver.With its Transceiver can transceiver design, this part can be incorporated into a wide range of solutions.This wide receiver can be placed on any Surface Mount-type PCB or development board.A power supply of 4.75V~5.25V is used by this differential driver.There can be up to 1/1 eligible receivers/drivers on the field at the same time with this electronic part.In most applications, this ic receiver is used in environments where 0°C~70°C is the operating temperature.An output voltage range of 5V is sufficient to run this line driver ic efficiently.Wide receiver has 8 terminations built in for driving or receiving signals from data.Transceiver comes with 8 standard pinouts that meet the market's requirements.As the base part number MAX483 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.The driver IC has improved power dissipation control.Through optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size is reduced dramatically.It is important to note that this ic receiver had a maximum resolution of 1 bits.Typically, the resolution of this receiver is specified to be 1 bits.There is a voltage input supply of 5V required for the operation of this integrated circuit.There is a subcategory named Line Driver or Receivers for this rf transceiver module.This driver IC is designed to operate from a 5V power supply.ICs implement a total of 1 transceivers.In addWide receiverion to delivering voltage at 3V, Wide receiver also has the abilWide receivery to measure voltage.
MAX483ECSA+T Features
Tape & Reel (TR) package
8 pin count
8 pins
5V power supply
MAX483ECSA+T Applications
There are a lot of Maxim Integrated MAX483ECSA+T Drivers/Receivers/Transceivers applications.
- Automation systems
- Portable radio
- Military satellite communications
- Changeing the frequency from IF to RF
- Wired telephone
- 1x/2x Fiber Channel
- Cordless telephone
- Remote controls
- Transmission stations
- Low power, low voltage systems
