MAX4852ETE+

60ns, 40ns SPDT 4.5Ohm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4852 16 Pins 2nA 3V 16-WFQFN Exposed Pad

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4852ETE+
Package: 16-WFQFN Exposed Pad
Datasheet: PDF
Stock: 261
Description: 60ns, 40ns SPDT 4.5Ohm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4852 16 Pins 2nA 3V 16-WFQFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-WFQFN Exposed Pad
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2000
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	4.5Ohm
Terminal Finish	TIN
Subcategory	Multiplexer or Switches
Max Power Dissipation	1.67W
Technology	CMOS
Terminal Position	QUAD
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.5mm
Base Part Number	MAX4852
Output	SEPARATE OUTPUT
Pin Count	16
Polarity	Non-Inverting
Power Supplies	3/5V
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Turn On Delay Time	60 ns
Data Rate	12 Mbps
Supply Type	Single
Turn-Off Delay Time	40 ns
-3db Bandwidth	100MHz
On-State Resistance (Max)	4.5Ohm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	80 dB
Current - Leakage (IS(off)) (Max)	2nA
Channel Capacitance (CS(off), CD(off))	20pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	60ns, 40ns
Charge Injection	8pC
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-95dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2V~5.5V
Height Seated (Max)	0.8mm
Length	3mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

MAX4852ETE+ Overview

Presented in 16-WFQFN Exposed Pad, this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 2:1. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. A 1 channel electronic part produces high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. On the other hand, analog switches can be constructed using SPDT switching circuits. There are 2 circuits in this multiplexer. Search with MAX4852 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 4.5Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 5.5V to a switch device. A analog switch ic that has a cost-effective Single supply type. 2V is the lowest voltage the electrical component should receive. For this digital switch to work, 1μA current would suffice. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. The analogue multiplexer may be damaged if voltage is greater than 1μA. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.