MAX4852ETE+T

60ns, 40ns SPDT 4.5Ohm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4852 16 Pins 2nA 3V 16-WFQFN Exposed Pad

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4852ETE+T
Package: 16-WFQFN Exposed Pad
Datasheet: PDF
Stock: 740
Description: 60ns, 40ns SPDT 4.5Ohm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4852 16 Pins 2nA 3V 16-WFQFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-WFQFN Exposed Pad
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2008
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	4.5Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	1.667W
Technology	CMOS
Terminal Position	QUAD
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.5mm
Base Part Number	MAX4852
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	5V
Polarity	Non-Inverting
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Turn On Delay Time	60 ns
Data Rate	12 Mbps
Supply Type	Single
Turn-Off Delay Time	40 ns
-3db Bandwidth	100MHz
On-State Resistance (Max)	4.5Ohm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	80 dB
Current - Leakage (IS(off)) (Max)	2nA
Channel Capacitance (CS(off), CD(off))	20pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	60ns, 40ns
Charge Injection	8pC
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-95dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2V~5.5V
Height Seated (Max)	0.8mm
Length	3mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX4852ETE+T Overview

As the electronic part is packed in 16-WFQFN Exposed Pad, international shipping is convenient. High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 2:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 16 terminations. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. There is an electrical component included in the 16 series. Unlike digital switches, these are based on SPDT switching circuits. A total of 2 circuits make up this switch device. Try searching for MAX4852 variants of the analog switch ic. This digital multiplexer has 4.5Ohm internal resistance. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. There should be 2V voltage fed to the electrical part below 2V. For this digital switch to work, 1μA current would suffice. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating voltages range from 5V.