MAX4854HETE+
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN Exposed Pad |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | TIN |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX4854 |
| Pin Count | 16 |
| JESD-30 Code | S-XQCC-N16 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| -3db Bandwidth | 150MHz |
| On-State Resistance (Max) | 9Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 12pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 60ns, 40ns |
| Charge Injection | 8pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switch-on Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
MAX4854HETE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-WFQFN Exposed Pad. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. The operating temperature is extended to around -40°C~85°C TA. Totally, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 16 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 4. MAX4854 can be used to search for analog multiplexer variants. Using a single voltage supply, this switch device consumes 2V~5.5V volts.
MAX4854HETE+ Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 150MHz
MAX4854HETE+ Applications
There are a lot of Maxim Integrated MAX4854HETE+ Analog Switches & Multiplexers ICs applications.
- Data switching
- Communications systems
- Private Branch Exchange (PBX)
- Data Acquisition Systems
- Sample hold systems
- Avionics test equipment
- Ultrasound
- PDAs
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio signal routing
