MAX485CPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX485 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 900μA |
| Data Rate | 2.5Mbps |
| Output Characteristics | 3-STATE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
| Number of Transceivers | 1 |
| Receive Delay-Max | 200 ns |
| Simplex/Duplex | Half Duplex |
| Transmit Delay-Max | 60 ns |
| Output Low Current-Max | 0.004A |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX485CPA+ Overview
LED drivers with the enhanced 8-DIP (0.300, 7.62mm) package will be able to drive a variety of common LEDs with ease.The Tube package houses this receiver.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.Any Through Hole-type PCB or development board can be used with this wide receiver.This differential driver consumes 4.75V~5.25V for its power supplyThis electronic part can have?up to 1/1 eligible receivers/drivers on the field at once.?The operating temperature of this ic receiver is 0°C~70°C. It is primarily designed for applications with low temperatures.Driver ICs with a supply voltage range of 5V can operate efficiently.In this wide receiver, 8 terminations are integrated for driving and receiving signals from data.As a standard package, this transceiver comes with a 8-pin layout that follows the market standard.Since the base part number MAX485 uniquely identifies the product type, temperature, package, etc., you can use it to find more variations.An enhanced power dissipation control driver IC featuring 8 pins.Optical transceiver package size is greatly reduced due to downsizing of the ICs and high-density Through Hole mounting technologies.An important feature of this ic receiver was its 1-bit resolution capability.As a rule of thumb, this receiver is typically specified with a resolution of 1 bits.There are two types of input voltage supply available for this IC, 5V.An additional subcategory named Line Driver or Receivers can be created for this rf transceiver module.There is one driver IC that is designed to operate from a 5V power supply, and only one driver IC in total.Transceivers implemented by this IC total 1 in total.An input voltage of 500μA is recommended for this integrating circuit to be able to drive LEDs.
MAX485CPA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX485CPA+ Applications
There are a lot of Maxim Integrated MAX485CPA+ Drivers/Receivers/Transceivers applications.
- Televisions
- Broadcast application
- Wireless network systems
- Ethernet circuitry
- Low power, low voltage systems
- Wired telephone
- Structural bonding
- Aircraft navigation
- Metro access rings
- Optical sub-assembly (OSA)
