MAX485CSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 506.605978mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX485 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Voltage | 5V |
| Interface | RS-422, RS-485 |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 500μA |
| Data Rate | 2.5Mbps |
| Output Characteristics | 3-STATE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 50mV |
| Number of Transceivers | 1 |
| Receive Delay-Max | 200 ns |
| Simplex/Duplex | Half Duplex |
| Transmit Delay-Max | 60 ns |
| Output Low Current-Max | 0.004A |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX485CSA+ Overview
Due to the enhanced 8-SOIC (0.154, 3.90mm Width) package, this driver IC is excellent for driving common LEDs.Tube package is used to mount this receiver.It has proved to be a valuable component for a variety of applications since it is a Transceiver can transceiver.On any Surface Mount-type PCB or development board, this wide receiver can be placed.Power supply requirements for this differential driver are 4.75V~5.25V.As many as 1/1 receivers/drivers are eligible for use on this electronic part.For applications where the operating temperature is 0°C~70°C, this ic receiver was designed primarily.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.8 terminations are integrated into this wide receiver for driving and receiving signals from data.A package consisting of 8 market standard pinouts is provided with this integrated circuit.Since the base part number MAX485 describes the product type, temperature, package, etc., you might get more options by searching with it.An enhanced power dissipation driver IC with 8 pins.Through optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size is reduced dramatically.There is a capability of 1-bit resolution with this ic receiver.Typically, the resolution of this receiver is specified to be 1 bits.As a result of the design of this transceiver module, the input voltage supply is designed to operate at 5V.3 volts.A Line Driver or Receivers subcategory can be assigned to this rf transceiver module.There is one driver IC in this package which is intended to be operated by 5V of power.It implements 1 transceivers in total.It has the ability to drive LEDs with an input voltage of up to about 500μA with the help of this integrating circuit.
MAX485CSA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX485CSA+ Applications
There are a lot of Maxim Integrated MAX485CSA+ Drivers/Receivers/Transceivers applications.
- Low power, low voltage systems
- Desktop PC
- Radio transmission
- Car alarm systems
- transmission relay
- Automation systems
- Wireless projection application for conferences
- Copper connection network
- VoIP phones
- Aircraft navigation
