MAX485CSA
| Parameters | |
|---|---|
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
| Interface Standard | EIA-422; EIA-485 |
| Receive Delay-Max | 200 ns |
| Transmit Delay-Max | 60 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 1.5 V |
| High Level Input Current-Max | 0.001A |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | 1 RECEIVER ACTIVE UNDER SHUTDOWN; TRISTATABLE RECEIVER |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX485 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 0.9mA |
| Data Rate | 2.5Mbps |
| Output Characteristics | 3-STATE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
MAX485CSA Overview
Designed for common LEDs, this driver IC features an enhanced 8-SOIC (0.154, 3.90mm Width) package.The Tube package houses this receiver.The Transceiver can transceiver technology has enabled this part to power many solutions for a variety of uses.PCB or development board with Surface Mount-type connectors can accommodate this wide receiver.This differential driver consumes 4.75V~5.25V for its power supplyThis electronic part can have?up to 1/1 eligible receivers/drivers on the field at once.?In most applications, this ic receiver is used in environments where 0°C~70°C is the operating temperature.An operating voltage range of 5V is suitable for this line driver ic.In order to drive and receive signals from data, this wide receiver has 8 terminations integrated.It is packaged with 8 pinouts that are market standard for this particular transceiver.This part number MAX485 can be used to search for more variants based on the product type, temperature, package, etc.It was possible to achieve a 1-bit resolution through this ic receiver.There is usually a 1-bit resolution specified for this receiver when it is used.In this category, this rf transceiver module belongs to the Line Driver or Receivers subcategory.There is one driver IC in this package which is intended to be operated by 5V of power.The 1 RECEIVER ACTIVE UNDER SHUTDOWN; TRISTATABLE RECEIVER function of this optical transceiver module improves the overall stability and accuracy of signal management.The VCC pin of the ic receiver should receive enough but not more than 0.9mA of input current.
MAX485CSA Features
Tube package
8 pin count
5V power supply
MAX485CSA Applications
There are a lot of Maxim Integrated MAX485CSA Drivers/Receivers/Transceivers applications.
- Telecom applications
- Servers
- Tuner
- Radio transmission
- Precision geodetic measurement
- Wireless showroom
- Clock radio
- Fiber-to-the-desktop
- Wireless smart house
- Sensor reporting
