MAX485ECPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX485 |
| Pin Count | 8 |
| Output Voltage | 3V |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 500μA |
| Propagation Delay | 60 ns |
| Data Rate | 2.5Mbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
| Number of Transceivers | 1 |
| Receive Delay-Max | 200 ns |
| Simplex/Duplex | Half Duplex |
| Output Low Current-Max | 0.004A |
| High Level Input Current-Max | 0.000002A |
| Height | 4.572mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX485ECPA+ Overview
Driver ICs with enhanced 8-DIP (0.300, 7.62mm) packages are excellent for driving LEDs with common characteristics.In the Tube package, this receiver is mounted.The Transceiver can transceiver type enables this part to be used in a wide range of applications.Ideally, you should place this wide receiver on a Through Hole-type PCB or development board.Power supply requirements for this differential driver are 4.75V~5.25V.Up to 1/1 receivers/drivers can be installed simultaneously on this electronic part.For applications where the operating temperature is 0°C~70°C, this ic receiver was designed primarily.This line driver ic can operate efficiently with a supply voltage range of 5V.This wide receiver has 8 terminations for driving and receiving data signals.This transceiver is packaged with 8 market standard pinoutsSince the part number MAX485 represents the product type, temperature, package, etc., you can try searching with that number to find more variants.This is a 8-pin driver IC with enhanced power dissipation control.A dramatic reduction in package size is achieved through optical transceiver downsizing and high-density Through Hole mounting technologies.It was possible to achieve a 1-bit resolution through this ic receiver.This receiver is typically specified with a resolution of 1 bits. There are two types of input voltage supply available for this IC, 5V.Line Driver or Receivers is a subcategory of this rf transceiver module.There is one driver IC in this package which is intended to be operated by 5V of power.In total, there are 1 transceivers implemented by this module isolated transceiver.The device is capable of delivering voltage at 3V.
MAX485ECPA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX485ECPA+ Applications
There are a lot of Maxim Integrated MAX485ECPA+ Drivers/Receivers/Transceivers applications.
- Copper connection network
- Servers
- Home theater wiring-free
- Aircraft navigation
- Car radio
- Wired telephone
- Wireless access points
- Indoor ad hoc meeting
- Routers
- Metro access rings
