MAX485EEPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX485 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 0.9mA |
| Data Rate | 2.5Mbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
| Receive Delay-Max | 200 ns |
| Transmit Delay-Max | 60 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 1.5 V |
| High Level Input Current-Max | 0.000002A |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX485EEPA+ Overview
Due to the enhanced 8-DIP (0.300, 7.62mm) package, this driver IC is excellent for driving common LEDs.Tube package is used for this receiver.The Transceiver can transceiver type enables this part to be used in a wide range of applications.A Through Hole-type PCB or development board can be used to place this wide receiver.In terms of power supply, this differential driver utilizes 4.75V~5.25V.Up to 1/1 receivers/drivers can be installed simultaneously on this electronic part.IC receiver is designed for applications with a temperature of -40°C~85°C.An output voltage range of 5V is sufficient to run this line driver ic efficiently.For driving and receiving signals from data, this wide receiver has 8 terminations integrated.The pinouts for this transceiver are standardized to meet the needs of the market.The base part number MAX485 identifies the product type, temperature, package, etc., so you can search for more variants by using it.Wide receiver with enhanced power dissipation control, 8-pin.In this ic receiver, the resolution was able to be set to a maximum of 1 bits.There are typically 1 bits of resolution specified in the specifications of this receiver.A Line Driver or Receivers subcategory can be assigned to this rf transceiver module.Driver ICs are designed to work with a 5V power supply and this driver IC is one of them.The VCC pin of the ic receiver should receive enough but not more than 0.9mA of input current.
MAX485EEPA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX485EEPA+ Applications
There are a lot of Maxim Integrated MAX485EEPA+ Drivers/Receivers/Transceivers applications.
- Aircraft positioning
- Precision engineering measurement
- Bar, KTV wireless entertainment
- IPTV front end
- Structural bonding
- Bridges
- Remote controls
- Remote controls
- Interconnection between switches and computers
- Fiber-to-the-desktop
