MAX488ECPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX488 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 0.25mA |
| Data Rate | 250kbps |
| Output Characteristics | TOTEM-POLE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 70mV |
| Receive Delay-Max | 2000 ns |
| Transmit Delay-Max | 2000 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 1.5 V |
| High Level Input Current-Max | 0.000002A |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX488ECPA+ Overview
LED drivers with the enhanced 8-DIP (0.300, 7.62mm) package will be able to drive a variety of common LEDs with ease.The Tube package houses this receiver.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.On any Through Hole-type PCB or development board, you can install this wide receiver.Power supply for this differential driver is 4.75V~5.25V.At any given time, there can be up to 1/1 eligible receivers/drivers for this electronic part.In most applications, this ic receiver is used in environments where 0°C~70°C is the operating temperature.Driver ICs with a supply voltage range of 5V can operate efficiently.This integrated circuit has 8 terminations designed for driving and receiving signals from data.A package consisting of 8 market standard pinouts is provided with this integrated circuit.Since the base part number MAX488 describes the product type, temperature, package, etc., you might get more options by searching with it.An enhanced power dissipation control driver IC featuring 8 pins.This ic receiver provided a 1-bit resolution capability. There is usually a 1-bit resolution specified for this receiver when it is used.An additional subcategory named Line Driver or Receivers can be created for this rf transceiver module.Driver ICs such as this one are designed to operate from 5V power sources.There should be enough current supplied to the VCC pin of the part, but not more than 0.25mA.
MAX488ECPA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX488ECPA+ Applications
There are a lot of Maxim Integrated MAX488ECPA+ Drivers/Receivers/Transceivers applications.
- WDM transmission
- Wireless interactive experience
- Wireless multimedia center in smart home
- VoIP phones
- Fiber distributed data interface (FDDI)
- Wireless transmission
- Single to Multimode Fiber Conversion
- Cordless telephone
- Aircraft positioning
- Satellite radio receiver
