MAX489ESD+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | 5A991.B.4 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX489 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 0.25mA |
| Data Rate | 250kbps |
| Output Characteristics | 3-STATE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 70mV |
| Interface Standard | EIA-422; EIA-485 |
| Receive Delay-Max | 2000 ns |
| Transmit Delay-Max | 2000 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 1.5 V |
| High Level Input Current-Max | 0.000001A |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX489ESD+ Overview
Designed for common LEDs, this driver IC features an enhanced 14-SOIC (0.154, 3.90mm Width) package.This receiver is mounted in the Tube package.Since this part is a Transceiver can transceiver, a number of solutions have been able to utiliTransceivere it for various purposes.You can place this wide receiver to any Surface Mount-type PCB or development board.In terms of power supply, this differential driver utilizes 4.75V~5.25V.There can be up to 1/1 eligible receivers/drivers on the field at the same time with this electronic part.IC receiver likes this one are designed for use in applications where operating temperatures are -40°C~85°C.Driver ICs with a supply voltage range of 5V can operate efficiently.For driving and receiving signals from data, this wide receiver has 14 terminations integrated.This transceiver is packaged with 14 market standard pinoutsYou can search with MAX489 to get more variants of this part, since it identifies the product type, temperature, package, etc.It is a 14-pin driver IC with enhanced power dissipation controls.There is a capability of 1-bit resolution with this ic receiver.There is typically a resolution of 1 bits specified with this receiver.An additional subcategory named Line Driver or Receivers can be created for this rf transceiver module.This driver IC is designed to operate from a 5V power supply.The VCC pin of the ic receiver should receive enough but not more than 0.25mA of input current.
MAX489ESD+ Features
Tube package
14 pin count
14 pins
5V power supply
MAX489ESD+ Applications
There are a lot of Maxim Integrated MAX489ESD+ Drivers/Receivers/Transceivers applications.
- Data center
- Cable network front end
- Point-to-point networking
- WDM transmission
- Wireless network systems
- Aircraft positioning
- Wireless interactive experience
- Ethernet circuitry
- Wireless multimedia center in smart home
- Automation systems
