MAX4947ETG+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-WFQFN Exposed Pad |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 5.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.67W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4947 |
| Pin Count | 24 |
| Number of Channels | 3 |
| Number of Circuits | 3 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Max Supply Current | 10μA |
| Turn On Delay Time | 800 ns |
| Turn-Off Delay Time | 800 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 5.5Ohm |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 3nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 800ns, 800ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.8mm |
| Length | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4947ETG+ Overview
The electronic component is convenient to ship overseas because it is packed in a 24-WFQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 2:2 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 24. A electrical component with 3 channels is capable of high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. The electrical component body receives 24 pins. Circuits based on DPDT switching are used to construct these analog switch ics. This multiplexer is composed of 3 circuits. Try searching with MAX4947 if you're looking for variants. A 5.5Ohm internal resistance characterizes this multiplexer. You can find the functions of the 24 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. 1.8V should be the lowest voltage fed to the electronic component. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. If put voltage greater than 10μA on the device, damage may be caused to the analogue multiplexer.
MAX4947ETG+ Features
3 Channels
Switch Circuit: DPDT
-3db Bandwidth: 300MHz
MAX4947ETG+ Applications
There are a lot of Maxim Integrated MAX4947ETG+ Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Automotive applications
- Multi-Line E1 Interface Cards
- ATM
- HDTV
- Cable PC
- PDH Multiplexers
- Modems
- USB 1.1 signal switching circuits
- Cross Connects
