MAX4947ETG+T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 24-WFQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Resistance | 5.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4947 |
| Output | SEPARATE OUTPUT |
| Pin Count | 24 |
| Number of Channels | 3 |
| Number of Circuits | 3 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 5.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 3nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 800ns, 800ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 800ns |
| Switch-off Time-Max | 800ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.8mm |
| Length | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4947ETG+T Overview
Shipping overseas is convenient due to the electrical component's packing in 24-WFQFN Exposed Pad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:2. Operational temperature extended around -40°C~85°C TA. A total of 24 terminations have been recorded. This electronic part offers high-quality output due to its 3 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. An injection of 24 pins is performed into the body of the electrical component. Multiplexers built on a DPDT switching circuit are built. Circuits number 3 make up this analogue multiplexer. Using the MAX4947 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 5.5Ohm. To find out what the 24 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. In order for the electronic part to function properly, the lowest voltage should be 1.8V. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4947ETG+T Features
3 Channels
Switch Circuit: DPDT
-3db Bandwidth: 300MHz
MAX4947ETG+T Applications
There are a lot of Maxim Integrated MAX4947ETG+T Analog Switches & Multiplexers ICs applications.
- Medical
- DSLAMs
- Digital access cross connects
- HDTV
- Audio and video routing
- Data switching
- Public switching systems
- RGB switches
- E1 Network Equipment
- High reliability control systems
