MAX4948EBA+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 25-WFBGA, CSPBGA |
| Number of Pins | 25 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 25 |
| ECCN Code | EAR99 |
| Resistance | 5.5Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 976mW |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 6 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX4948 |
| Output | SEPARATE OUTPUT |
| Pin Count | 25 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 6 |
| Number of Circuits | 6 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Turn On Delay Time | 800 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 800 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 5.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 3nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 800ns, 800ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Length | 2.54mm |
| RoHS Status | ROHS3 Compliant |
MAX4948EBA+T Overview
As the electronic part is packed in 25-WFBGA, CSPBGA, international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. In total, 25 terminations have occurred. High-quality output is provided by the electronic component's 6 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. This electrical component is included in the 25 series of products. On the other hand, analog switches can be constructed using SPDT switching circuits. A total of 6 circuits make up this switch device. Try searching with MAX4948 if you're looking for variants. Internally, this switch multiplexer has a resistance of 5.5Ohm. The datasheets for the 25 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. 1.8V should be the lowest voltage fed to the electronic component. It would be sufficient to run this analogue multiplexer with 10μA current. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 10μA. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. A voltage of 5V can be used to operate the electronic component.
MAX4948EBA+T Features
6 Channels
Switch Circuit: SPDT
10μA Supply Current
-3db Bandwidth: 300MHz
MAX4948EBA+T Applications
There are a lot of Maxim Integrated MAX4948EBA+T Analog Switches & Multiplexers ICs applications.
- Public switching systems
- PBX interfaces
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Avionics and Military Systems
- ATM
- Remote Powered Equipment
- Cellular phones
- Digital access cross connects
- Channelized and Unchannelized DS3 applications
- USB 1.1 signal switching circuits
