MAX4948ETG+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-WFQFN Exposed Pad |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 5.5Ohm |
| HTS Code | 8542.39.00.01 |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.67W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 6 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4948 |
| Pin Count | 24 |
| Power Supplies | 3/5V |
| Number of Channels | 6 |
| Number of Circuits | 6 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Turn On Delay Time | 800 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 800 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 5.5Ohm |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 3nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 800ns, 800ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 750μm |
| Length | 4.1mm |
| Width | 4.1mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4948ETG+ Overview
Shipping overseas is convenient due to the electrical component's packing in 24-WFQFN Exposed Pad. In order to provide high reliability, an advanced packaging method Tube is used. It is mounted in the position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. A total of 24 terminations have been recorded. As a result of its 6 channels, this electronic component provides high-quality output. When a voltage supply of 3V is used, the electronic component should be turned on and run. A total of 24 pins are injected into the electrical part body. A SPDT switching circuit is used to build these analog multiplexers. 6 circuits are used in this analogue multiplexer. MAX4948 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 5.5Ohm. Please refer to the datasheets for 24 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. A low voltage of 1.8V should be applied to the electronic component. The switch device would be able to operate with 10μA current. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. Put voltage above 10μA on the multiplexer to cause damage.
MAX4948ETG+ Features
6 Channels
Switch Circuit: SPDT
10μA Supply Current
-3db Bandwidth: 300MHz
MAX4948ETG+ Applications
There are a lot of Maxim Integrated MAX4948ETG+ Analog Switches & Multiplexers ICs applications.
- ATM
- Precision instrumentation
- Sample hold systems
- Cable PC
- SONET
- Modems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Ultrasound
- Signal routing between systems
- T1/E1 Terminals
