MAX494CPD+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 6V |
| Base Part Number | MAX494 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Operating Supply Current | 150μA |
| Nominal Supply Current | 150μA |
| Output Current | 30mA |
| Slew Rate | 0.2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 74 dB |
| Current - Input Bias | 25nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 500 kHz |
| Unity Gain BW-Nom | 500 kHz |
| Voltage Gain | 104dB |
| Average Bias Current-Max (IIB) | 0.075μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.06μA |
| Length | 19.05mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX494CPD+ Overview
Packaging for the buffer amplifier is in the form of a 14-DIP (0.300, 7.62mm) case. An op amp of this type is a General Purpose-type. There is a Tube case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 14. There are a total of 14 pins on this op amp. Please take in mind that op amp should be run at 6V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. There are 14 pins on this chip. Op amp ic rates 200μV for input offset voltage. This electronic part is best mounted with type Through Hole. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . As long as the supply current of the chip does not exceed 150μA, this op amp ic can operate. You should keep the voltage gain at 104dB for the time being. As far as the device is concerned, buffer amplifier has 4 channels. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 3V voltage.
MAX494CPD+ Features
14 Pins
supply voltage of 6V
104dB voltage gain
Output Type: Rail-to-Rail
MAX494CPD+ Applications
There are a lot of Maxim Integrated MAX494CPD+ Instrumentational OP Amps applications.
- single/dual op amp sum and difference circuits
- High-frequency data acquisition systems
- Active probe
- Power generator
- Hand-held batteries
- Measurements of Wheatstone bridge
- Ultrasound transducers
- Displayers for aircraft and air transportation control systems
- Image computer boards
- ECG equipment
