MAX4968CEXB+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 64-LFBGA |
| Surface Mount | YES |
| Number of Pins | 64 |
| Weight | 170.210537mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tray |
| Published | 2014 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 64 |
| Resistance | 34Ohm |
| HTS Code | 8542.39.00.01 |
| Max Power Dissipation | 1.97W |
| Technology | BICMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.8mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX4968 |
| Number of Channels | 1 |
| Number of Circuits | 16 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.37V |
| Max Supply Current | 50μA |
| Turn On Delay Time | 5 μs |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 3.5 μs |
| Max Dual Supply Voltage | 12.5V |
| -3db Bandwidth | 30MHz |
| On-State Resistance (Max) | 34Ohm |
| Min Dual Supply Voltage | 10V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| On-state Resistance Match-Nom | 0.54Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 5μs, 3.5μs |
| Charge Injection | 150pC |
| Channel-to-Channel Matching (ΔRon) | 1.02 Ω |
| Crosstalk | -69dB @ 5MHz |
| Switch-on Time-Max | 5000ns |
| Switch-off Time-Max | 3500ns |
| Voltage - Supply, Single (V+) | 10V~12.5V |
| Height Seated (Max) | 1.3mm |
| Length | 7mm |
| RoHS Status | ROHS3 Compliant |
MAX4968CEXB+ Overview
Shipping overseas is convenient due to the electrical component's packing in 64-LFBGA. The advanced packaging method Tray provides high reliability. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. In total, there have been 64 terminations. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 3.3V volts, the electrical part can be powered up and run. A SPST - NO switching circuit is used to build these analog multiplexers. A total of 16 circuits make up this switch device. Look for analog switch ic variants by searching with MAX4968. There is 34Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 64 pins functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analog switch ics with Dual, Single supply type are cost-effective. A low voltage of 2.37V should be applied to the electronic component. Analogue multiplexers require a 10V~12.5V voltage to drain from a single voltage supply. If you put voltage higher than 50μA on the digital multiplexer, damage may occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 12.5V. When using dual power supplies, you should attach at least 10V.
MAX4968CEXB+ Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 30MHz
MAX4968CEXB+ Applications
There are a lot of Maxim Integrated MAX4968CEXB+ Analog Switches & Multiplexers ICs applications.
- Modems
- DSUs
- Multiplexers
- Communication systems
- Switching Systems
- Isolation
- PDAs
- Video switching
- Power routing
- Ultrasound
