MAX4993EVB+

630ns, 2μs DPDT 500mOhm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4993 10 Pins 100nA 2.7V 10-UFQFN

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4993EVB+
Package: 10-UFQFN
Datasheet: PDF
Stock: 231
Description: 630ns, 2μs DPDT 500mOhm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4993 10 Pins 100nA 2.7V 10-UFQFN(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-UFQFN
Number of Pins	10
Operating Temperature	-40°C~85°C TA
Packaging	Strip
Published	2009
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
ECCN Code	EAR99
Resistance	500mOhm
Subcategory	Multiplexer or Switches
Max Power Dissipation	559mW
Technology	BICMOS
Terminal Position	QUAD
Number of Functions	1
Supply Voltage	2.7V
Terminal Pitch	0.4mm
Base Part Number	MAX4993
Output	SEPARATE OUTPUT
Pin Count	10
Power Supplies	3/5V
Number of Channels	2
Number of Circuits	1
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Max Supply Current	6μA
Turn On Delay Time	630 ms
Supply Type	Single
Turn-Off Delay Time	2 μs
On-State Resistance (Max)	500mOhm
Multiplexer/Demultiplexer Circuit	2:2
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	100nA
Channel Capacitance (CS(off), CD(off))	45pF
On-state Resistance Match-Nom	0.003Ohm
Switch Circuit	DPDT
Switch Time (Ton, Toff) (Max)	630ns, 2μs
Channel-to-Channel Matching (ΔRon)	3m Ω
Crosstalk	-110dB @ 20kHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	2000ns
Voltage - Supply, Single (V+)	1.8V~5.5V
Height Seated (Max)	0.55mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX4993EVB+ Overview

Shipping overseas is convenient with the electronic component packed in 10-UFQFN. In order to provide high reliability, an advanced packaging method Strip is used. A switch device like this is mounted in Surface Mount. 2:2 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. There are 10 terminations totally. The electronic part delivers high-quality output through its 2 channels. Powered by a 2.7V voltage supply, the electrical part should be switched on and run. A total of 10 pins are injected into the electrical part body. The analog switch ics are built using DPDT switching circuits. The circuits in this analogue multiplexer number 1. Try searching for MAX4993 variants of the analog switch ic. There is 500mOhm internal resistance in this digital multiplexer. Please refer to the datasheets for 10 pins functions. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 1.8V. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. Putting voltage greater than 6μA on the multiplexer may cause damage. There are SEPARATE OUTPUT outputs on this analog switch ic.