MAX4996ETG+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-WFQFN Exposed Pad |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.228W |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Number of Functions | 3 |
| Supply Voltage | 2.8V |
| Terminal Pitch | 0.4mm |
| Base Part Number | MAX4996 |
| Output | SEPARATE OUTPUT |
| Pin Count | 24 |
| Number of Channels | 2 |
| Number of Circuits | 3 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.5V |
| Operating Supply Current | 5μA |
| Nominal Supply Current | 10μA |
| Turn On Delay Time | 6 μs |
| Supply Type | Single |
| Turn-Off Delay Time | 100 μs |
| -3db Bandwidth | 670MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 250nA |
| Channel Capacitance (CS(off), CD(off)) | 2.5pF 4pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 100μs, 6μs |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 10000ns |
| Switch-off Time-Max | 6000ns |
| Voltage - Supply, Single (V+) | 2.5V~5.5V |
| Height Seated (Max) | 0.85mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4996ETG+ Overview
Shipping overseas is convenient due to the electrical component's packing in 24-WFQFN Exposed Pad. To ensure high reliability, a new packaging method Tube is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:2. Operation at a temperature around -40°C~85°C TA. A total of 24 terminations have been recorded. As a result of its 2 channels, this electronic component provides high-quality output. Powered by a 2.8V voltage supply, the electrical part should be switched on and run. Electronic part bodies are injected with 24 pins. A DPDT switching circuit is used to build these analog multiplexers. There are 3 circuits in this multiplexer. Search with MAX4996 if you are looking for analog multiplexer variants. This digital multiplexer has 4Ohm internal resistance. For details about the functions of 24 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. 2.5V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 5μA. Using a single voltage supply, this switch device consumes 2.5V~5.5V volts. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX4996ETG+ Features
2 Channels
Switch Circuit: DPDT
5μA Supply Current
-3db Bandwidth: 670MHz
MAX4996ETG+ Applications
There are a lot of Maxim Integrated MAX4996ETG+ Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Relay Replacement
- DVD-R
- Video switching
- E1 Multiplexer
- Fault Tolerant Systems
- Wireless Local Loop
- Data switching
- Data Acquisition Systems
- CSU
