Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
24-WFQFN Exposed Pad |
Number of Pins |
24 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2008 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
24 |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
1.228W |
Technology |
BICMOS |
Terminal Position |
QUAD |
Number of Functions |
3 |
Supply Voltage |
2.8V |
Terminal Pitch |
0.4mm |
Base Part Number |
MAX4996 |
Output |
SEPARATE OUTPUT |
Pin Count |
24 |
Number of Channels |
2 |
Number of Circuits |
3 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2.5V |
Operating Supply Current |
5μA |
Nominal Supply Current |
10μA |
Max Supply Current |
10μA |
Turn On Delay Time |
100 μs |
Supply Type |
Single |
Turn-Off Delay Time |
6 μs |
-3db Bandwidth |
670MHz |
On-State Resistance (Max) |
4Ohm |
Multiplexer/Demultiplexer Circuit |
2:2 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
250nA |
Channel Capacitance (CS(off), CD(off)) |
2.5pF 4pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
DPDT |
Switch Time (Ton, Toff) (Max) |
100μs, 6μs |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
10000ns |
Switch-off Time-Max |
6000ns |
Voltage - Supply, Single (V+) |
2.5V~5.5V |
Height Seated (Max) |
0.85mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
MAX4996LETG+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 24-WFQFN Exposed Pad. High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:2. The operating temperature is extended to around -40°C~85°C TA. There are 24 terminations totally. Due to its 2 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 2.8V, it should be turned on and run. Electronic part bodies are injected with 24 pins. Multiplexers built on a DPDT switching circuit are built. The circuits in this analogue multiplexer number 3. Search with MAX4996 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 4Ohm. You can find the functions of the 24 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. 2.5V should be the lowest voltage fed to the electronic component. An operating current of 5μA would be sufficient for this switch device. The voltage required by this switch device is 2.5V~5.5V, draining from a single voltage supply. Put voltage above 10μA on the multiplexer to cause damage. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4996LETG+ Features
2 Channels
Switch Circuit: DPDT
5μA Supply Current
-3db Bandwidth: 670MHz
MAX4996LETG+ Applications
There are a lot of Maxim Integrated MAX4996LETG+ Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Microprocessor Controlled Analog Systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PBX interfaces
- Communication systems
- High reliability control systems
- Remote Powered Equipment
- Transmit
- High speed data transmission line cards
- Sample-and-hold systems