MAX5003CEE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.635mm |
| Base Part Number | MAX5003 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 12V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 18.75V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 10.75V~18.75V |
| Control Features | Frequency Control, On Time Control, Soft Start |
| Input Voltage (Min) | 7.4V |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 50kHz~300kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Max Frequency | 1.2MHz |
| Max Duty Cycle | 75 % |
| Length | 4.89mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX5003CEE+T Overview
It comes in a 16-SSOP (0.154, 3.90mm Width) package, so switching controller can be used for most applications. There is sufficient capacity to generate switching controller for outputs 1. Tape & Reel (TR) is the solid enclosure in which PMIC is packaged. It is capable of handling Transistor Driver dc switching's outputs (s). 10.75V~18.75V is the operating voltage and supply voltage of the dc control. A 0°C~70°C TA dc switcher is not a problem. With this switching controller, you can switch at 50kHz~300kHz. As it has a Surface Mount value, it can be used for general dc dc regulator. Frequency Control, On Time Control, Soft Start is used for efficient switching control in the dcdc regulator. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. Terminal (s) of the switching converters are designed at the DUAL position. 16 terminations with a variety of function. This dc dc converter ic uses a variety of control techniques, including PULSE WIDTH MODULATION. You can find other relevant dc to dc converter ics by searching "MAX5003". There are a total of 16 pins on switching converter. Switching converter is a type of Switching Regulator or Controllers in particular. dc dc voltage regulators should have a minimum input voltage of 7.4V. Based on the test statistics, DC regulator outputs voltage 12V. You should note down the dc dc regulator's usual output current of 1A when you start a project. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 75 %. The Surface Mount makes DC switcher suitable for most applications and prototypes. There is a maximum frequency of 1.2MHz for this dc regulators. If the user wishes to run the voltage regulator dc to dc in a circuit safely and reliably, they should apply 18.75V.
MAX5003CEE+T Features
Transistor Driver Outputs
Switching Frequency: 50kHz~300kHz
Frequency Control, On Time Control, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 75 %
MAX5003CEE+T Applications
There are a lot of Maxim Integrated MAX5003CEE+T DC to DC converter applications.
- Radio equipment
- Shearing machines
- Planers
- Motor controller circuits
- Linear guide
- Medical equipment
- Remotely powered electric motors
- Window air conditioners
- Communication system
- Large fire protection systems
