MAX5094BASA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 186.993455mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | IT CAN ALSO OPERATE WITH CURRENT MODE |
| Subcategory | Switching Regulator or Controllers |
| Max Power Dissipation | 470.6mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 1MHz |
| Base Part Number | MAX5094 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 5V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Operating Supply Current | 3mA |
| Output Configuration | Positive, Isolation Capable |
| Power Dissipation | 471mW |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | 7.6V~30V |
| Quiescent Current | 32μA |
| Control Features | Frequency Control |
| Topology | Flyback, Forward Converter |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 10kHz~500kHz |
| Max Input Voltage | 26.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 15ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 22 ns |
| Nominal Input Voltage | 26.5V |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 49.8 % |
| Input Current | 3mA |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX5094BASA+ Overview
The switching controller fits in the 8-SOIC (0.154, 3.90mm Width) package and is ideal for most applications. There is enough capacity in the dc motor controller to generate the output for the 1 input. PMIC packaging is solid with a Tube enclosure. There are Transistor Driver dc switching's output (s) that it can handle. A 7.6V~30V voltage is supplied to the dc control and used for operating it. A -40°C~125°C TJ dc switcher is not a problem. There is a switch at 10kHz~500kHz that can be used with this controller. It is suitable for general dc dc regulator when it is set to Surface Mount. Frequency Control provides dcdc regulator efficient switching control. An analog IC SWITCHING CONTROLLER is connected to the switch converters. There are a DUAL terminal on the switching converters. There are many different types of terminations for 8. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. It is inputted with a DC switcher's voltage of 15V. Other relevant dc to dc converter ics can be found by searching "MAX5094". 8 pins are present on switching converter. Specially, switching converter corresponds to type Switching Regulator or Controllers. A 5V voltage of DC regulator was detected in the test statistics. You should note down the dc dc regulator's usual output current of 2A when you start a project. As a result of this, the maximum duty cycle of the voltage regulator dc to dc must remain 49.8 % during power-up and power-down. In most applications and prototypes, DC switcher's Surface Mount makes it suitable. The switching controller works at a frequency of 1MHz. To better satisfy the need, DC to DC voltage regulator has a value of IT CAN ALSO OPERATE WITH CURRENT MODE. In dormant mode, 32μA is used. It is possible to set the input voltage as 26.5V for nominal working statuses. The maximum input voltage of the dc switcher is 26.5V, so users need to limit the voltage accordingly. There is a 3mA volt supply current. If there is 3mA current flow input, then the switching converter could operate.
MAX5094BASA+ Features
Transistor Driver Outputs
Switching Frequency: 10kHz~500kHz
Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 49.8 %
Frequency: 1MHz
IT CAN ALSO OPERATE WITH CURRENT MODE
MAX5094BASA+ Applications
There are a lot of Maxim Integrated MAX5094BASA+ DC to DC converter applications.
- Constant current circuits
- Medical equipment
- Magnetohydrodynamic power
- Drilling machines
- Gear/thread machining machines
- Various precision measuring instruments
- Smoke exhaust equipment
- Large fire protection systems
- Smart grid
- Industrial robots
