MAX5932ESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Feature | Latched Fault |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Hot Swap Controller |
| Applications | General Purpose |
| Subcategory | Power Management Circuits |
| Technology | BICMOS |
| Voltage - Supply | 9V~80V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 24V |
| Base Part Number | MAX5932 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Supply Voltage-Max (Vsup) | 80V |
| Power Supplies | 24V |
| Supply Voltage-Min (Vsup) | 9V |
| Number of Channels | 1 |
| Power Dissipation | 470mW |
| Adjustable Threshold | YES |
| Current - Supply | 1.4mA |
| Supply Current-Max (Isup) | 3.5mA |
| Internal Switch(s) | No |
| Programmable Features | Current Limit, Fault Timeout, OVP, Slew Rate, UVLO |
| Feature Pins | FB, ON, PWRGD, TIMER |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
MAX5932ESA+T Overview
It's included in the 8-SOIC (0.154, 3.90mm Width) package.Channel 1 is currently available.In the form of a Tape & Reel (TR), it is packaged.In total, it has 8 terminations.A device's terminal position is DUAL.Total number of pins is 8.An efficient supply voltage is possible with 24V.Surface Mount is set up this way.This electrical component is classified as Hot Swap Controller.Ensure reliable operation by setting the temperature to -40°C~85°C.There are General Purpose applications on the device.A feature of Latched Fault describes it.Hot-swappable device should work if you use a 9V~80VV power source.There are numbers in the MAX5932 family that include it.There is nothing else in Power Management Circuits but this gadget.Current Limit, Fault Timeout, OVP, Slew Rate, UVLO features are programmable.1.4mA is currently in short supply.Surface Mount is the direction in which it is positioned.Normally, Vsup should remain above 9V.80V is set for Vsup (maximum supply voltage).Part 24V uses a power supply that has a voltage.A maximum supply current of 3.5mA is required for the device to operate.
MAX5932ESA+T Features
The terminal position of 8
Features of Latched Fault
Programmable features of Current Limit, Fault Timeout, OVP, Slew Rate, UVLO
MAX5932ESA+T Applications
There are a lot of Maxim Integrated MAX5932ESA+T hot swap controllers applications.
- Limitting the inrush current
- Hard drive
- Solid state circuit breakers
- DC boost circuit
- Modern analog communication
- Overcurrent protection
- Storage network
- Undervoltage protection
- Short-circuit protection in real time
- Automatic restart after load failure
