MAX6303CSA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ADJUSTABLE WATCHDOG TIMEOUT, PUSH/PULL OR OPEN-DRAIN OUTPUT OPTIONS |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX6303 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 4μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | Adjustable/Selectable |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 2.8ms Minimum |
| Supply Current-Max (Isup) | 0.007mA |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6303CSA+T Overview
This power management consists of 8 mounting terminals on which it can be mounted. Tape & Reel (TR)-packaging is used. There are 1 functions included in this PMIC so that you can refer to them. It is possible to find on this power management a series of 1 channels. Please refer to power management for 8-SOIC (0.154, 3.90mm Width) functions. Several of the benefits of this PMIC are also shared by other Simple Reset/Power-On Reset products. The package peak reflow temperature is specified to be 260. The supervisor is always powered by a 5V volt supply. Power management conducts at a voltage of 1. Power management is included in the Surface Mount mount. There is a subcategory called Power Management Circuits for this power management. 8 pins are present in total in this power management. The pins of the power management system count 8. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. Power management recommends the Surface Mount mounting type. We recommend setting the supervisors to 0°C~70°C TA degrees. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. In order to maintain a stable supply current for the power management, 4μA is the recommended value. In addition, IC management are other features such as [0], to mention only a few. It is always advisable to use MAX6303, the base supervisor number, when searching for similar PMICs from the manufacturer.
MAX6303CSA+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
4μA operating supply current
MAX6303CSA+T Applications
There are a lot of Maxim Integrated MAX6303CSA+T Voltage Supervisors applications.
- Detection of phase loss
- Power distribution systems of CCU
- Important electronics for automotive safety
- Dash board
- Stable power system
- Battery-powered equipment
- Low voltage/high power - AI, GPU
- Magnetic resonance imaging
- Electronics installed in the vehicle
- Utility meter
