MAX6304EPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Additional Feature | ADJUSTABLE WATCHDOG TIMEOUT, PUSH-PULL OUTPUT |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX6304 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.31V |
| Operating Supply Current | 4μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active High |
| Voltage - Threshold | Adjustable/Selectable |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 2.8ms Minimum |
| Supply Current-Max (Isup) | 0.007mA |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX6304EPA Overview
This voltage supervisor has a total of 8 mounting terminals that can be used for mounting. A Tube package is used to package the power management. For your reference, this IC power includes a list of 1 functions. This power managment ic consists of 1 channels, each of which can be used independently. For your reference, this PMIC includes a list of 8-DIP (0.300, 7.62mm) functions. As with other Simple Reset/Power-On Reset products, this IC management also offers a wide range of benefits. Specifies a reflow peak temperature of 245 for the package during reflow. During operation, the power ic is supplied with a voltage of 5V. Power management conducts at a voltage of 1. The power management is mounted by Through Hole. Power Management Circuits is a subcategory of this PMIC chip. In total, it has 8 pins on IC management. 8 pins are present on the power management system. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1.31V volts. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Through Hole is the recommended mounting type. The temperature of the supervisors should be set to this range: -40°C~85°C TA. As a result of this supervisor's operation, the output voltage is Push-Pull, Totem Pole. There is a 4μA supply current present in the power management. The other features include, for example, [0], which is just one example. You can always use MAX6304, the base supervisor number, to search for similar PMICs of the manufacturer.
MAX6304EPA Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.31V
4μA operating supply current
MAX6304EPA Applications
There are a lot of Maxim Integrated MAX6304EPA Voltage Supervisors applications.
- DSP
- Battery-powered equipment
- Power distribution systems of infant care room
- Magnetic resonance imaging
- Rechargeable batteries
- Detection of phase loss
- Automotive permanent magnet synchronous motors
- Computer applications
- Leakage current detection
- Electronics installed in the vehicle
