MAX6315US26D2+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-253-4, TO-253AA |
| Number of Pins | 4 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Base Part Number | MAX6315 |
| Output | Open Drain or Open Collector |
| Pin Count | 4 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 5μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 20ms Minimum |
| Min Reset Threshold Voltage | 2.58V |
| Max Reset Threshold Voltage | 2.68V |
| Threshold Voltage | 2.63 |
| Undervoltage Threshold | 2.58V |
| Overvoltage Threshold | 2.68V |
| Length | 2.92mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6315US26D2+T Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 4 in total. Packaging is in the form of a Tape & Reel (TR). Please find attached 1 functions for your reference in this IC power. Depending on the power managment ic you are looking at, you can find a total of 1 channels. Please refer to power management for TO-253-4, TO-253AA functions. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. There is a voltage supply of 3.6V for the PMIC chip, and the chip conducts at that voltage. Power ics operate at 1 supply voltages. Power management is included in the Surface Mount mount. In total, IC powers are 4 pins on the board. Pin count of the power management is 4. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Mounting type Surface Mount is recommended. Temperature setting for the supervisors should be -40°C~125°C TA. The output voltage of this power managment ic during operation is Open Drain or Open Collector. There is a supply current of 5μA for the power management. A similar IC managements number of the manufacturer can always be found by using MAX6315, the base power ics number.
MAX6315US26D2+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
5μA operating supply current
MAX6315US26D2+T Applications
There are a lot of Maxim Integrated MAX6315US26D2+T Voltage Supervisors applications.
- Smart meter
- Dash board
- Radar
- Household appliances
- Microcontroller system
- Power distribution systems of infant care room
- Medical-specific isolation transformer
- Battery cars
- Consumer electronics
- Analog circuit
