MAX6323AUT29-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Type | Watchdog Circuit |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 696mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Base Part Number | MAX6323 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 6 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 27μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 2.93V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 100ms Minimum |
| Supply Current-Max (Isup) | 0.057mA |
| Min Reset Threshold Voltage | 2.85V |
| Max Reset Threshold Voltage | 3V |
| Undervoltage Threshold | 2.85V |
| Overvoltage Threshold | 3V |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX6323AUT29-T Overview
Power management is mounted through 6 terminals. Packaged in the form of a Tape & Reel (TR), power management is easy to use. There are 1 functions included in this PMIC so that you can refer to them. Power management consists of 1 channels, each of which can be used independently. For your reference, this PMIC includes a list of SOT-23-6 functions. As with other Watchdog Circuit products, this IC management also offers a wide range of benefits. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 245. During operation, the power ic is supplied with a voltage of 3V. When a supply voltage of 1 is applied to the power ic, it conducts. By Surface Mount, IC management has been mounted. It is possible to subcategorize this power ic as a Power Management Circuits chip. Power management has a total of 6 pins. There are 6 pins on the power managment ic. There should be a minimum voltage supply (Vsup) of 1.2V for this PMIC. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. In this case, Surface Mount is the recommended mounting type. We recommend setting the supervisors to -40°C~125°C TA degrees. During normal operation, this power managment ic can generate Push-Pull, Totem Pole of output voltage. There is a supply current of 27μA for the power management. It is always advisable to use MAX6323, the base supervisor number, when searching for similar PMICs from the manufacturer.
MAX6323AUT29-T Features
Watchdog Circuit type
Minimum supply voltage of 1.2V
27μA operating supply current
MAX6323AUT29-T Applications
There are a lot of Maxim Integrated MAX6323AUT29-T Voltage Supervisors applications.
- Insulation fault location system
- Power distribution systems of operating room
- Dash board
- Electric heating appliances
- Precision measurement
- Automotive permanent magnet synchronous motors
- Important electronics for automotive safety
- Embedded computing
- Satellite navigation
- Smart meter
