MAX6326UR31+T
| Parameters | |
|---|---|
| Length | 2.92mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Base Part Number | MAX6326 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 500nA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 3.08V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 100ms Minimum |
| Min Reset Threshold Voltage | 3.034V |
| Max Reset Threshold Voltage | 3.126V |
| Threshold Voltage | +3.08V |
| Undervoltage Threshold | 3.034V |
| Overvoltage Threshold | 3.126V |
MAX6326UR31+T Overview
As you can see, this power management is mounted through 3 terminals. Power management is packaged in a Tape & Reel (TR) way. There are 1 functions included in this PMIC so that you can refer to them. Depending on the power managment ic you are looking at, you can find a total of 1 channels. In this IC management you will find TO-236-3, SC-59, SOT-23-3 functions for you to refer to. There are many benefits that this IC power shares with other Simple Reset/Power-On Reset products as well. Specifies a reflow peak temperature of 260 for the package during reflow. When a supply voltage of 3V is applied to the power ic, it conducts. A supply voltage of 1 is used to conduct the PMIC chip. Power management is included in the Surface Mount mount. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. Taking into account all of the pins, this power management has a total of 3. 3 pins are present on the power management system. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.2V. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 5.5V volts. Surface Mount is the recommended mounting type. Temperature setting for the supervisors should be -40°C~85°C TA. Power management has an output of Push-Pull, Totem Pole during operation. It is estimated that the voltage supervisor's supply current is 500nA. It is always advisable to use MAX6326, the base supervisor number, when searching for similar PMICs from the manufacturer.
MAX6326UR31+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
500nA operating supply current
MAX6326UR31+T Applications
There are a lot of Maxim Integrated MAX6326UR31+T Voltage Supervisors applications.
- Medical-specific insulation monitor
- Electrical fire monitoring system
- DC stabilized power supply module
- Consumer electronics
- FPGA design
- Fire equipment power monitoring system
- Microcontroller system
- Dash board
- Stable power system
- Insulation fault location system
