MAX6328XR23+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-70, SOT-323 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Strip |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 174mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Output | Open Drain or Open Collector |
| Pin Count | 3 |
| JESD-30 Code | R-PDSO-G3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 500nA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.32V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 100ms Minimum |
| Min Reset Threshold Voltage | 2.285V |
| Max Reset Threshold Voltage | 2.355V |
| Threshold Voltage | +2.3V |
| Undervoltage Threshold | 2.285V |
| Overvoltage Threshold | 2.355V |
| Length | 2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6328XR23+T Overview
Power management is mounted through 3 terminals. Packaged in the form of a Strip, power management is easy to use. Please refer to this PMIC for 1 functions. This power managment ic consists of 1 channels, each of which can be used independently. The purpose of this IC power is to provide you with a reference of SC-70, SOT-323 functions. There are a lot of similarities between this IC power and other Simple Reset/Power-On Reset products. Packages are specified to have an average peak reflow temperature of 260. There is a voltage supply of 3V for the PMIC chip, and the chip conducts at that voltage. Power ics operate at 1 supply voltages. The mount is attached to Surface Mount. This power ic can be sub-categorized as Power Management Circuits. In total, IC powers are 3 pins on the board. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.2V. During this IC power, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Power management' mounting is recommended to be done with the Surface Mount type of mounting. You should set the supervisor's temperature during -40°C~85°C TA . During normal operation, this power managment ic can generate Open Drain or Open Collector of output voltage. For this power management, there is an 500nA volt supply current.
MAX6328XR23+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
500nA operating supply current
MAX6328XR23+T Applications
There are a lot of Maxim Integrated MAX6328XR23+T Voltage Supervisors applications.
- DVR
- Insulation fault location system
- Microprocessor system
- Battery cars
- Important electronics for automotive protection
- Power distribution systems of ICU
- Detection of phase loss
- External alarm
- Battery-powered equipment
- Detection of phase sequence
