MAX6338BUB
| Parameters | |
|---|---|
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 444mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX6338 |
| Output | Open Drain or Open Collector |
| Pin Count | 10 |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.5V |
| Operating Supply Current | 35μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.5V 3.3V 5V Adj |
| Number of Voltages Monitored | 4 |
| Reset Timeout | <1ms Minimum |
| Supply Current-Max (Isup) | 0.065mA |
| Undervoltage Threshold | 2.13V |
| Overvoltage Threshold | 2.25V |
| Height Seated (Max) | 1.1mm |
MAX6338BUB Overview
There are 10 terminals on this power management that allow it to be mounted. It is packaged with Tube. Please find attached 1 functions for your reference in this IC power. Depending on the power managment ic you are looking at, you can find a total of 4 channels. In this IC management you will find 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) functions for you to refer to. This IC power shares lots of benefits with other Multi-Voltage Supervisor products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 245. There is a voltage supply of 3V for the PMIC chip, and the chip conducts at that voltage. During operation, the power ic is supplied with a voltage of 4. The power management is mounted by Surface Mount. The power management belongs to the Power Management Circuits subcategory. Taking into account all of the pins, this power management has a total of 10. This power management has 10 pins. In order for this IC power to function, the supply voltage (Vsup) cannot be less than 2.5V. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. A Surface Mount mounting type is recommended. The supervisors should be set to the following temperature: -40°C~85°C TA. There is an output voltage of Open Drain or Open Collector from this supervisor when it is operating. The supervisor's supply current is specified to 35μA. A similar IC managements number of the manufacturer can always be found by using MAX6338, the base power ics number. The voltage supervisor requires a power source of 3/5V volts in order to work correctly.
MAX6338BUB Features
Multi-Voltage Supervisor type
Minimum supply voltage of 2.5V
35μA operating supply current
MAX6338BUB Applications
There are a lot of Maxim Integrated MAX6338BUB Voltage Supervisors applications.
- Data storage applications
- FPGA design
- Sensitive sensors
- Important electronics for automotive safety
- Medical-specific isolation transformer
- Display equipment
- Microcontroller system
- Automotive permanent magnet synchronous motors
- Detection of phase imbalance
- Multi-voltage system
