Parameters |
Undervoltage Threshold |
2.13V |
Overvoltage Threshold |
2.25V |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Width |
3mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2006 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Type |
Multi-Voltage Supervisor |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Power Management Circuits |
Max Power Dissipation |
444mW |
Technology |
BICMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Base Part Number |
MAX6338 |
Output |
Open Drain or Open Collector |
Pin Count |
10 |
Power Supplies |
3/5V |
Number of Channels |
4 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2.5V |
Operating Supply Current |
35μA |
Adjustable Threshold |
YES |
Watchdog Timer |
No |
Reset |
Active Low |
Voltage - Threshold |
2.19V 2.93V Adj Adj |
Number of Voltages Monitored |
4 |
Reset Timeout |
<1ms Minimum |
Supply Current-Max (Isup) |
0.065mA |
MAX6338KUB+ Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 10 in total. Tube-packaging is used. Please refer to this PMIC for 1 functions. A series of 4 channels can be found on this supervisor. Please find attached 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) functions for your reference in this IC power. Compared to other Multi-Voltage Supervisor products, this PMIC has a lot of benefits to offer. Specifies a reflow peak temperature of 260 for the package during reflow. IC management conducts at a voltage of 3V. There is a voltage supply of 4 for the PMIC chip, and the chip conducts at that voltage. The mount is attached to Surface Mount. It is possible to subcategorize this power ic as a Power Management Circuits chip. In total, it has 10 pins on IC management. The pins of the power management system count 10. There should be a minimum voltage supply (Vsup) of 2.5V for this PMIC. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. A Surface Mount mounting type is recommended. The supervisors should be set to the following temperature: -40°C~85°C TA. Power management has an output of Open Drain or Open Collector during operation. The supervisor's supply current is specified to 35μA. A similar IC managements number of the manufacturer can always be found by using MAX6338, the base power ics number. The power management must be powered by 3/5V volts to function properly.
MAX6338KUB+ Features
Multi-Voltage Supervisor type
Minimum supply voltage of 2.5V
35μA operating supply current
MAX6338KUB+ Applications
There are a lot of Maxim Integrated MAX6338KUB+ Voltage Supervisors applications.
- DC stabilized power supply module
- DVR
- Radar
- emergency room
- Military communications
- Satellite navigation
- Solar power charger
- Military electronics
- Leakage current detection
- Electronics installed in the vehicle