MAX6365LKA26+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | MANUAL RESET INPUT |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 700mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.8V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX6365 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 2.5/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 15μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 150ms Minimum |
| Supply Current-Max (Isup) | 0.05mA |
| Min Reset Threshold Voltage | 2.55V |
| Max Reset Threshold Voltage | 2.7V |
| Undervoltage Threshold | 2.55V |
| Overvoltage Threshold | 2.7V |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6365LKA26+T Overview
As you can see, this power management is mounted through 8 terminals. Packaged in the form of a Tape & Reel (TR), power management is easy to use. To assist you, this IC power includes 1 functions. Power management consists of 2 channels, each of which can be used independently. For your reference, this PMIC includes a list of SOT-23-8 functions. It is a IC power that shares many benefits with other products from the Battery Backup Circuit line. According to the specification, the package's peak reflow temperature is specified to be 260. A supply voltage of 2.8V is used to conduct the PMIC chip. A supply voltage of 1 is used to conduct the PMIC chip. The power management is mounted by Surface Mount. Power Management Circuits is a subcategory of this PMIC chip. There are a total of 8 pins on power management. 8 pins make up the power management. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 0V. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. The recommended mounting type is Surface Mount. It is recommended to set the supervisor's temperature to this range: -40°C~85°C TA. While this power management is operating, it will output Push-Pull, Totem Pole as the output voltage. It is estimated that the voltage supervisor's supply current is 15μA. There are also other features in the software such as [0], just to mention a few. For similar manage ics search of the manufacturer, you can always refer to MAX6365, the base PMIC number. To operate this power management, you will need at least 2.5/5V volts of power.
MAX6365LKA26+T Features
Battery Backup Circuit type
Minimum supply voltage of 0V
15μA operating supply current
MAX6365LKA26+T Applications
There are a lot of Maxim Integrated MAX6365LKA26+T Voltage Supervisors applications.
- Fire equipment power monitoring system
- Electrical fire monitoring system
- DSP
- Detection of phase loss
- Functional modules
- Automotive permanent magnet synchronous motors
- Radar
- Battery cars
- Smart meter
- Important electronics for automotive protection
