MAX6366LKA29+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WATCH DOG TIMER |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 700mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.8V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX6366 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 2.5/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 15μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 2.93V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 150ms Minimum |
| Supply Current-Max (Isup) | 0.05mA |
| Min Reset Threshold Voltage | 2.85V |
| Max Reset Threshold Voltage | 3V |
| Undervoltage Threshold | 2.85V |
| Overvoltage Threshold | 3V |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6366LKA29+T Overview
This voltage supervisor has a total of 8 mounting terminals that can be used for mounting. There is a Tape & Reel (TR)-packaging method applied to IC management. Power management is possible to find a series of 1 functions. A series of 2 channels can be found on this supervisor. Please find attached SOT-23-8 functions for your reference in this IC power. Compared to other Battery Backup Circuit products, this PMIC has a lot of benefits to offer. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. A supply voltage of 2.8V is used to conduct the PMIC chip. During operation, the power ic is supplied with a voltage of 1. Power management is included in the Surface Mount mount. There is a subcategory of this power ic known as Power Management Circuits. There are a total of 8 pins on power management. This power management system has 8 pins. IC management can only work with a supply voltage of 0V volts. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. Power management recommends the Surface Mount mounting type. The supervisors should be set to the following temperature: -40°C~85°C TA. While in operation, this supervisor has a voltage output of Push-Pull, Totem Pole. As far as the supply current of the power management is concerned, it is 15μA. There are also other features in the software such as [0], just to mention a few. You can always use MAX6366, the base supervisor number, to search for similar PMICs of the manufacturer. To operate this power management, you will need at least 2.5/5V volts of power.
MAX6366LKA29+T Features
Battery Backup Circuit type
Minimum supply voltage of 0V
15μA operating supply current
MAX6366LKA29+T Applications
There are a lot of Maxim Integrated MAX6366LKA29+T Voltage Supervisors applications.
- Medical-specific insulation monitor
- Precision measurement
- Power distribution systems of infant care room
- Transformer load monitoring equipment
- Radio
- Smartphones
- Battery-powered equipment
- Multi-voltage system
- Embedded computing
- Radar
