MAX6370KA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Watchdog Circuit |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Analog Waveform Generation Functions |
| Max Power Dissipation | 700mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX6370 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.5V |
| Operating Supply Current | 10μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Number of Voltages Monitored | 1 |
| Reset Timeout | Adjustable/Selectable |
| Height | 1.3mm |
| Length | 3mm |
| Width | 1.75mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6370KA+T Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. It is packaged with Tape & Reel (TR). For your reference, this IC power includes a list of 1 functions. On this supervisor, there is a series of 1 channels that can be found. In this PMIC, you can find SOT-23-8 functions for your reference. There are a lot of similarities between this IC power and other Watchdog Circuit products. IC management is specified that the package peak reflow temperature should be 260. IC management conducts in a 3V-voltage supply. When a supply voltage of 1 is applied to the power ic, it conducts. The power management is mounted by a Surface Mount-axis. There is a subcategory of this power ic known as Analog Waveform Generation Functions. In total, the power management has 8 pins in it. The pins of the power management system count 8. There should be a minimum voltage supply (Vsup) of 2.5V for this PMIC. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. Surface Mount mounting is recommended. We recommend setting the supervisors to -40°C~125°C TA degrees. While in operation, this supervisor has a voltage output of Push-Pull, Totem Pole. There is a 10μA supply current present in the power management. You can always use MAX6370, the base supervisor number, to search for similar PMICs of the manufacturer. There is a requirement for 3/5V power to power this power management.
MAX6370KA+T Features
Watchdog Circuit type
Minimum supply voltage of 2.5V
10μA operating supply current
MAX6370KA+T Applications
There are a lot of Maxim Integrated MAX6370KA+T Voltage Supervisors applications.
- Electric heating appliances
- Insulation fault location system
- Satellite navigation
- Medical-specific isolation transformer
- Display equipment
- Network equipment
- Important electronics for automotive protection
- Radio
- Leakage current detection
- Automotive permanent magnet synchronous motors
