banner_page

MAX6381LT23D3+T

1.8V6 Terminals 6-Pin MAX6381 Voltage supervisor1 Channels Min 1V Max 5.5V


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX6381LT23D3+T
  • Package: 6-WFDFN
  • Datasheet: PDF
  • Stock: 139
  • Description: 1.8V6 Terminals 6-Pin MAX6381 Voltage supervisor1 Channels Min 1V Max 5.5V (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 6-WFDFN
Number of Pins 6
Operating Temperature -40°C~125°C TA
Packaging Tape & Reel (TR)
Published 2012
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 6
ECCN Code EAR99
Type Simple Reset/Power-On Reset
Terminal Finish GOLD
Subcategory Power Management Circuits
Max Power Dissipation 167.7mW
Technology BICMOS
Terminal Position DUAL
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 1.8V
Terminal Pitch 0.5mm
Base Part Number MAX6381
Output Push-Pull, Totem Pole
Pin Count 6
Number of Channels 1
Max Supply Voltage 5.5V
Min Supply Voltage 1V
Operating Supply Current 7μA
Adjustable Threshold NO
Watchdog Timer No
Reset Active Low
Voltage - Threshold 2.31V
Number of Voltages Monitored 1
Reset Timeout 140ms Minimum
Min Reset Threshold Voltage 2.26V
Max Reset Threshold Voltage 2.37V
Undervoltage Threshold 1.54V
Overvoltage Threshold 1.61V
Height Seated (Max) 0.8mm
RoHS Status ROHS3 Compliant

MAX6381LT23D3+T Overview


This voltage supervisor has a total of 6 mounting terminals that can be used for mounting. Power management is packaged in a Tape & Reel (TR) way. In this IC power you will find 1 functions for you to refer to. On this supervisor, there is a series of 1 channels that can be found. Please find attached 6-WFDFN functions for your reference in this IC power. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. Specifies a reflow peak temperature of 260 for the package during reflow. The supervisor is always powered by a 1.8V volt supply. Power ics operate at 1 supply voltages. By Surface Mount, IC management has been mounted. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. A total of 6 pins are located on this power management. There are 6 pins on the power managment ic. There should be a minimum voltage supply (Vsup) of 1V for this PMIC. Voltage (Vsup) shouldn't exceed 5.5V volts in this PMIC. The recommended mounting type for IC management is Surface Mount. Temperature setting for the supervisors should be -40°C~125°C TA. While in operation, this supervisor has a voltage output of Push-Pull, Totem Pole. There is a supply current of 7μA for the power management. It is always advisable to use MAX6381, the base supervisor number, when searching for similar PMICs from the manufacturer.

MAX6381LT23D3+T Features


Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
7μA operating supply current

MAX6381LT23D3+T Applications


There are a lot of Maxim Integrated MAX6381LT23D3+T Voltage Supervisors applications.

  • DVR
  • Analog circuit
  • Detection of phase imbalance
  • Military communications
  • Battery cars
  • Computer applications
  • Utility meter
  • Refrigeration
  • Battery-powered equipment
  • Multi-voltage system

Write a review

Note: HTML is not translated!
    Bad           Good