MAX6381LT42D2+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-WFDFN |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Gold (Au) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 167.7mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX6381 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 6 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 7μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.2V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 20ms Minimum |
| Min Reset Threshold Voltage | 4.1V |
| Max Reset Threshold Voltage | 4.31V |
| Undervoltage Threshold | 1.54V |
| Overvoltage Threshold | 1.61V |
| Height Seated (Max) | 0.8mm |
| RoHS Status | ROHS3 Compliant |
MAX6381LT42D2+T Overview
This power management consists of 6 mounting terminals on which it can be mounted. Packaged in the form of a Tape & Reel (TR), power management is easy to use. There are 1 functions included in this PMIC so that you can refer to them. Power management consists of 1 channels, each of which can be used independently. Please find attached 6-WFDFN functions for your reference in this IC power. Several of the benefits of this PMIC are also shared by other Simple Reset/Power-On Reset products. IC management is specified that the package peak reflow temperature should be 260. When 1.8V is applied to the power ic, it conducts. IC management conducts in a 1-voltage supply. The mount is provided by Surface Mount. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. In total, IC powers are 6 pins on the board. 6 pins make up the power management. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1V volts. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 5.5V volts. A Surface Mount mounting type is recommended. It is recommended that the supervisor be set to this temperature: -40°C~125°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. It is estimated that the voltage supervisor's supply current is 7μA. A similar IC managements number of the manufacturer can always be found by using MAX6381, the base power ics number.
MAX6381LT42D2+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
7μA operating supply current
MAX6381LT42D2+T Applications
There are a lot of Maxim Integrated MAX6381LT42D2+T Voltage Supervisors applications.
- Military communications
- Important electronics for automotive protection
- Utility meter
- FPGA design
- Efficient information transmission
- Cloud computing
- Set top box
- Detection of phase imbalance
- Medical-specific isolation transformer
- Leakage protection
