MAX6456UT26S+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Terminal Finish | Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 696mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.95mm |
| Base Part Number | MAX6456 |
| Output | Open Drain or Open Collector |
| Pin Count | 6 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 7μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.625V Adj |
| Number of Voltages Monitored | 2 |
| Reset Timeout | 140ms Minimum |
| Threshold Voltage | +2.63V |
| Height Seated (Max) | 1.45mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6456UT26S+T Overview
As you can see, this power management is mounted through 6 terminals. A Tape & Reel (TR) package is used to package the power management. Please find attached 1 functions for your reference in this IC power. This power managment ic consists of 1 channels, each of which can be used independently. Please find attached SOT-23-6 functions for your reference in this IC power. There are a lot of similarities between this IC management and other Multi-Voltage Supervisor products. The package peak reflow temperature is specified to be 260. Manage ics operate at 3.3V supply voltages. There is a voltage supply of 2 for the PMIC chip, and the chip conducts at that voltage. By Surface Mount, IC management has been mounted. A IC power such as this can be classified as a Power Management Circuits power management system. In total, it has 6 pins on IC management. Pin count of the power management is 6. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. The recommended mounting type for IC management is Surface Mount. Temperature setting for the supervisors should be -40°C~85°C TA. There is an output voltage of Open Drain or Open Collector from this supervisor when it is operating. It is estimated that the voltage supervisor's supply current is 7μA. You can always use MAX6456, the base supervisor number, to search for similar PMICs of the manufacturer.
MAX6456UT26S+T Features
Multi-Voltage Supervisor type
Minimum supply voltage of 1V
7μA operating supply current
MAX6456UT26S+T Applications
There are a lot of Maxim Integrated MAX6456UT26S+T Voltage Supervisors applications.
- Important electronics for automotive protection
- Power distribution systems of infant care room
- Analog circuit
- Automotive permanent magnet synchronous motors
- Medical-specific insulation monitor
- Leakage current detection
- DSP
- Set top box
- Utility meter
- FPGA design
