MAX6460UT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin (Sn) |
| Additional Feature | UNDERVOLTAGE LOCKOUT |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 696mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Base Part Number | MAX6460 |
| Output | Open Drain or Open Collector |
| Pin Count | 6 |
| Number of Channels | 1 |
| Max Supply Voltage | 28V |
| Min Supply Voltage | 4V |
| Operating Supply Current | 6.5μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active High |
| Voltage - Threshold | Adjustable/Selectable |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 50μs Typical |
| Threshold Voltage | +1.228V |
| Length | 2.9mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6460UT+T Overview
There are 6 terminals on this power management that allow it to be mounted. It is packaged with Tape & Reel (TR). Power management is possible to find a series of 1 functions. This power managment ic consists of 1 channels, each of which can be used independently. In this IC management you will find SOT-23-6 functions for you to refer to. There are a lot of similarities between this IC management and other Simple Reset/Power-On Reset products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. The supervisor is always powered by a 5V volt supply. When a supply voltage of 1 is applied to the power ic, it conducts. Surface Mount mounts power management on the wall. There is a subcategory of this power ic known as Power Management Circuits. In total, the power management has 6 pins in it. This power management has 6 pins. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 4V volts. This IC power should be powered by no more than 28V volts of supply voltage (Vsup). Power management recommends the Surface Mount mounting type. It is recommended that the supervisor be set to this temperature: -40°C~125°C TA. During normal operation, this power managment ic can generate Open Drain or Open Collector of output voltage. Supplied with a operating current of 6.5μA, this PMIC is capable of fully function as specified. There are also other features in the software such as [0], just to mention a few. You can always use MAX6460, the base supervisor number, to search for similar PMICs of the manufacturer.
MAX6460UT+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 4V
6.5μA operating supply current
MAX6460UT+T Applications
There are a lot of Maxim Integrated MAX6460UT+T Voltage Supervisors applications.
- External alarm
- Military electronics
- Medical-specific insulation monitor
- Radar
- Automotive permanent magnet synchronous motors
- Detection of phase imbalance
- Magnetic resonance imaging
- Electrical fire monitoring system
- Digitally controlled LDO regulators circuit
- Leakage current detection
