MAX6466XR26+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-70, SOT-323 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 228.6mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX6466 |
| Output | Open Drain or Open Collector |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 3.5μA |
| Max Supply Current | 3.5μA |
| Adjustable Threshold | NO |
| Accuracy | 2.5 % |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.6V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 150ms Minimum |
| Min Reset Threshold Voltage | 2.561V |
| Max Reset Threshold Voltage | 2.639V |
| Threshold Voltage | +2.7V |
| Undervoltage Threshold | 2.561V |
| Overvoltage Threshold | 2.639V |
| Reset Delay Time | 260 ms |
| Length | 2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6466XR26+T Overview
It is mounted through 3 terminals on the power management. A Tape & Reel (TR) package is used to package the power management. Please refer to this PMIC for 1 functions. A series of 1 channels can be found on this supervisor. As a reference, this IC power includes SC-70, SOT-323 functions for your convenience. There are a lot of similarities between this IC power and other Simple Reset/Power-On Reset products. There is a specification for the peak reflow temperature of the package to be 260. There is a voltage supply of 5V for the PMIC chip, and the chip conducts at that voltage. Power ics operate at 1 supply voltages. The power management is mounted by Surface Mount. The power management system can be categorized as a Power Management Circuits chip. There are a total of 3 pins on power management. There are 3 pins on the supervisor. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 1V, which is the minimum supply voltage that should be applied. The maximum supply voltage (Vsup) in this PMIC should not exceed 6V volts. The mounting type of the supervisors is Surface MountThe temperature of the supervisors should be set to this range: -40°C~125°C TA. Power management has an output of Open Drain or Open Collector during operation. As far as the supply current of the power management is concerned, it is 3.5μA. It is always advisable to use MAX6466, the base supervisor number, when searching for similar PMICs from the manufacturer. At most, voltage supervisor can operate at a supply temperature of 3.5μA.
MAX6466XR26+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
3.5μA operating supply current
MAX6466XR26+T Applications
There are a lot of Maxim Integrated MAX6466XR26+T Voltage Supervisors applications.
- Sensitive sensors
- Insulation fault location system
- Power distribution systems of infant care room
- emergency room
- Automotive permanent magnet synchronous motors
- Military electronics
- Important electronics for automotive protection
- Dash board
- External alarm
- Medical-specific isolation transformer
