MAX6705TKA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 714mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX6705 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 12μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 3.08V Adj |
| Number of Voltages Monitored | 2 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 3V |
| Max Reset Threshold Voltage | 3.15V |
| Undervoltage Threshold | 3V |
| Overvoltage Threshold | 3.15V |
| Height Seated (Max) | 1.45mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6705TKA+T Overview
As you can see, this power management is mounted through 8 terminals. There is a Tape & Reel (TR)-packaging method applied to IC management. For your reference, this IC power includes a list of 1 functions. Power management consists of 1 channels, each of which can be used independently. IC management is packaged as a SOT-23-8 package. There are a lot of similarities between this IC power and other Multi-Voltage Supervisor products. As specified in the package specification, the peak reflow temperature of the package is set at 260. There is a voltage supply of 2 for the PMIC chip, and the chip conducts at that voltage. The mount is provided by Surface Mount. There is a subcategory called Power Management Circuits for this power management. Taking into account all of the pins, this power management has a total of 8. This power management has 8 pins. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.2V. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. The mounting type of the supervisors is Surface MountThe supervisors should be set to the following temperature: -40°C~125°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. It is estimated that the voltage supervisor's supply current is 12μA. A similar IC managements number of the manufacturer can always be found by using MAX6705, the base power ics number.
MAX6705TKA+T Features
Multi-Voltage Supervisor type
Minimum supply voltage of 1.2V
12μA operating supply current
MAX6705TKA+T Applications
There are a lot of Maxim Integrated MAX6705TKA+T Voltage Supervisors applications.
- Sensitive sensors
- Power communication system
- DC stabilized power supply module
- Display equipment
- Automotive permanent magnet synchronous motors
- Detection of phase sequence
- emergency room
- Important electronics for automotive protection
- DSP
- Dash board
