MAX6709LUB+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 444mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX6709 |
| Output | Open Drain or Open Collector |
| Pin Count | 10 |
| Power Supplies | 2.5/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 35μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 1.67V 3.08V Adj Adj |
| Number of Voltages Monitored | 4 |
| Reset Timeout | <1ms Minimum |
| Supply Current-Max (Isup) | 0.065mA |
| Undervoltage Threshold | 1.62V |
| Overvoltage Threshold | 1.71V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6709LUB+ Overview
It is mounted through 10 terminals on the power management. Power management is packaged in a Tube way. Power management is possible to find a series of 1 functions. There are 4 channels on this power managment ic that can be found in a series. In this PMIC, you can find 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) functions for your reference. Several of the benefits of this PMIC are also shared by other Multi-Voltage Supervisor products. Specifies a reflow peak temperature of 260 for the package during reflow. IC management conducts in a 5V-voltage supply. IC management is possible to find a succession of 4 voltages that have been checked. Using Surface Mount, IC management is mounted. This power ic can be sub-categorized as Power Management Circuits. Power management has a total of 10 pins. There are 10 pins on the power managment ic. Supply voltage (Vsup) should be at least 2V for this power management. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. Power management' mounting is recommended to be done with the Surface Mount type of mounting. The temperature of the supervisors should be set to this range: -40°C~85°C TA. There is an output voltage of Open Drain or Open Collector from this supervisor when it is operating. The supply current of the power management is 35μA. You can always use MAX6709, the base supervisor number, to search for similar PMICs of the manufacturer. To operate this power management, you will need at least 2.5/5V volts of power.
MAX6709LUB+ Features
Multi-Voltage Supervisor type
Minimum supply voltage of 2V
35μA operating supply current
MAX6709LUB+ Applications
There are a lot of Maxim Integrated MAX6709LUB+ Voltage Supervisors applications.
- Urban rail transit weak current power monitoring
- Military communications
- Display equipment
- Consumer electronics
- Dash board
- Power distribution systems of ICU
- Power distribution systems of operating room
- Magnetic resonance imaging
- Efficient information transmission
- emergency room
