MAX6726KASHD3+T
| Parameters | |
|---|---|
| Pin Count | 8 |
| Power Supplies | 1/5V |
| Number of Channels | 3 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 800mV |
| Operating Supply Current | 15μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 1.313V 2.925V Adj |
| Number of Voltages Monitored | 3 |
| Reset Timeout | 140ms Minimum |
| Undervoltage Threshold | 1.275V |
| Overvoltage Threshold | 1.35V |
| Height Seated (Max) | 1.45mm |
| Length | 2.9mm |
| Width | 1.625mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Terminal Finish | Gold (Au) - with Nickel (Ni) barrier |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 714mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX6726 |
| Output | Push-Pull, Push-Pull |
MAX6726KASHD3+T Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. Power management is packaged in a Tape & Reel (TR) way. There are 1 functions included in this PMIC so that you can refer to them. There are 3 channels on this power managment ic that can be found in a series. Please find attached SOT-23-8 functions for your reference in this IC power. This IC power shares lots of benefits with other Multi-Voltage Supervisor products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. Power ics operate at 3 supply voltages. Using Surface Mount, IC management is mounted. The power management system can be categorized as a Power Management Circuits chip. In total, the power management has 8 pins in it. The pins of the power management system count 8. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 800mV volts. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 5.5V volts. Surface Mount mounting is recommended. The temperature of the supervisors should be set to this range: -40°C~85°C TA. There is an output voltage of Push-Pull, Push-Pull from this supervisor when it is operating. The supervisor's supply current is specified to 15μA. If you want to search for similar IC managements of this manufacturer, you can always refer to MAX6726, which is the base power ics number. The voltage supervisor requires a power source of 1/5V volts in order to work correctly.
MAX6726KASHD3+T Features
Multi-Voltage Supervisor type
Minimum supply voltage of 800mV
15μA operating supply current
MAX6726KASHD3+T Applications
There are a lot of Maxim Integrated MAX6726KASHD3+T Voltage Supervisors applications.
- Microcontroller system
- emergency room
- Functional modules
- Insulation fault location system
- Efficient information transmission
- Rechargeable batteries
- Low voltage/high power - AI, GPU
- Dash board
- Detection of phase imbalance
- Important electronics for automotive safety
