MAX6834VXRD0+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-70, SOT-323 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 235mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.2V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX6834 |
| Output | Open Drain or Open Collector |
| Pin Count | 3 |
| JESD-30 Code | R-PDSO-G3 |
| Power Supplies | 0.4/3.3V |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 550mV |
| Operating Supply Current | 16μA |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 1.575V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 70μs Typical |
| Supply Current-Max (Isup) | 0.025mA |
| Min Reset Threshold Voltage | 1.53V |
| Max Reset Threshold Voltage | 1.62V |
| Threshold Voltage | +1.575V |
| Undervoltage Threshold | 1.53V |
| Overvoltage Threshold | 1.62V |
| Length | 2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6834VXRD0+T Overview
As you can see, this power management is mounted through 3 terminals. Tape & Reel (TR)-packaging is used. Please find attached 1 functions for your reference in this IC power. There are 1 channels available on this supervisor, and each channel has a different function. In this IC management you will find SC-70, SOT-323 functions for you to refer to. It is a IC power that shares many benefits with other products from the Simple Reset/Power-On Reset line. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. A supply voltage of 1.2V is used to conduct the PMIC chip. During operation, the power ic is supplied with a voltage of 1. The mount is provided by Surface Mount. The power management belongs to the Power Management Circuits subcategory. A total of 3 pins are located on this power management. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 550mV. The maximum supply voltage (Vsup) in this PMIC should not exceed 3.6V volts. In this case, Surface Mount is the recommended mounting type. The temperature of the supervisors should be set to this range: -40°C~85°C TA. As a result of this supervisor's operation, the output voltage is Open Drain or Open Collector. It is estimated that the voltage supervisor's supply current is 16μA. It is always advisable to use MAX6834, the base supervisor number, when searching for similar PMICs from the manufacturer. It requires 0.4/3.3V watts of power to operate this voltage supervisor.
MAX6834VXRD0+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 550mV
16μA operating supply current
MAX6834VXRD0+T Applications
There are a lot of Maxim Integrated MAX6834VXRD0+T Voltage Supervisors applications.
- Detection of phase loss
- Linux and server computing
- Detection of phase sequence
- Detection of phase imbalance
- Transformer load monitoring equipment
- Medical-specific insulation monitor
- Dash board
- Radar
- Automotive power systems
- Important electronics for automotive protection
