MAX6885ETP+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-WQFN Exposed Pad |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Max Power Dissipation | 1.702W |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.05V |
| Base Part Number | MAX6885 |
| Output | Open Drain, Push-Pull |
| Pin Count | 20 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.8V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1.1mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 6 Selectable Threshold Combinations |
| Number of Voltages Monitored | 6 |
| Reset Timeout | Adjustable/Selectable |
| Undervoltage Threshold | 167mV |
| Overvoltage Threshold | 1.017V |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
| Width | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX6885ETP+ Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 20 in total. In terms of packaging, power management follows the Tube model. To assist you, this IC power includes 1 functions. This power managment ic consists of 1 channels, each of which can be used independently. In this IC management you will find 20-WQFN Exposed Pad functions for you to refer to. Several of the benefits of this PMIC are also shared by other Multi-Voltage Supervisor products. Specifies a reflow peak temperature of 260 for the package during reflow. In a 3.05V supply voltage, the power management conducts. A supply voltage of 6 is used to conduct the PMIC chip. Surface Mount mounts power management on the wall. In total, IC powers are 20 pins on the board. Power managment ic pin count is 20. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 2.7V. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.8V volts. The mounting type of the supervisors is Surface MountWe recommend setting the supervisors to -40°C~85°C TA degrees. As this power managment ic operates, it is able to produce an output voltage of Open Drain, Push-Pull. Supplied with a operating current of 1.1mA, this PMIC is capable of fully function as specified. For similar manage ics search of the manufacturer, you can always refer to MAX6885, the base PMIC number.
MAX6885ETP+ Features
Multi-Voltage Supervisor type
Minimum supply voltage of 2.7V
1.1mA operating supply current
MAX6885ETP+ Applications
There are a lot of Maxim Integrated MAX6885ETP+ Voltage Supervisors applications.
- Cloud computing
- Utility meter
- Consumer electronics
- Refrigeration
- Military electronics
- Detection of phase imbalance
- Power distribution systems of CCU
- Important electronics for automotive safety
- Automotive permanent magnet synchronous motors
- Functional modules
