MAX691ACSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | EITHER VCC OR VBATT CAN GO TO 0V, IF THE OTHER IS GREATER THAN 2.0V |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.75V |
| Base Part Number | MAX691 |
| Output | Push-Pull, Push-Pull |
| Pin Count | 16 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Operating Supply Current | 100μA |
| Max Supply Current | 100μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height | 2.35mm |
| Length | 10.5mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX691ACSE+T Overview
There are 16 terminals on this power management that allow it to be mounted. Tape & Reel (TR)-packaging is used. To assist you, this IC power includes 1 functions. There are 1 channels available on this supervisor, and each channel has a different function. In this IC management you will find 16-SOIC (0.154, 3.90mm Width) functions for you to refer to. There are a number of benefits that this PMIC has in common with other Battery Backup Circuit manage ics. During the reflow process, a peak temperature of 260 is specified for the package. When a supply voltage of 4.75V is applied to the power ic, it conducts. Power ics operate at 1 supply voltages. Surface Mount mounts power management on the wall. It is possible to subcategorize this power ic as a Power Management Circuits chip. It has a total of 16 pins that are attached to IC management. 16 pins make up the power management. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 0V. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 5.5V volts. The recommended mounting type for IC management is Surface Mount. We recommend setting the supervisors to 0°C~70°C TA degrees. During normal operation, this power managment ic can generate Push-Pull, Push-Pull of output voltage. As far as the supply current of the power management is concerned, it is 100μA. There are also other features in the software such as [0], just to mention a few. It is always advisable to use MAX691, the base supervisor number, when searching for similar PMICs from the manufacturer. In order to operate this power management, it requires 5V volts of power. The maximum supply temperature voltage supervisor can handle is 100μA.
MAX691ACSE+T Features
Battery Backup Circuit type
Minimum supply voltage of 0V
100μA operating supply current
MAX691ACSE+T Applications
There are a lot of Maxim Integrated MAX691ACSE+T Voltage Supervisors applications.
- Insulation fault location system
- Network equipment
- DSP
- Solar power charger
- Precision measurement
- emergency room
- Satellite navigation
- External alarm
- Digitally controlled LDO regulators circuit
- Automotive permanent magnet synchronous motors
