banner_page

MAX691CWE+

5V16 Terminals 16-Pin MAX691 Voltage supervisor1 Channels Min 4.75V Max 5.5V


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX691CWE+
  • Package: 16-SOIC (0.295, 7.50mm Width)
  • Datasheet: PDF
  • Stock: 315
  • Description: 5V16 Terminals 16-Pin MAX691 Voltage supervisor1 Channels Min 4.75V Max 5.5V (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mounting Type Surface Mount
Package / Case 16-SOIC (0.295, 7.50mm Width)
Surface Mount YES
Number of Pins 16
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 1995
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Type Battery Backup Circuit
Terminal Finish Matte Tin (Sn)
Subcategory Power Management Circuits
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 5V
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number MAX691
Output Push-Pull, Push-Pull
Pin Count 16
Qualification Status Not Qualified
Power Supplies 5V
Number of Channels 1
Max Supply Voltage 5.5V
Min Supply Voltage 4.75V
Power Dissipation 600mW
Output Current 50mA
Adjustable Threshold NO
Reset Active High/Active Low
Voltage - Threshold 4.65V
Number of Voltages Monitored 1
Reset Timeout 35ms Minimum
Height 2.65mm
Width 7.5mm
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MAX691CWE+ Overview


There are 16 terminals on this power management that allow it to be mounted. Packaged in the form of a Tube, power management is easy to use. Please refer to this PMIC for 1 functions. A series of 1 channels can be found on this supervisor. IC management is packaged as a 16-SOIC (0.295, 7.50mm Width) package. There are a lot of similarities between this IC management and other Battery Backup Circuit products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 260. Manage ics operate at 5V supply voltages. IC management is possible to find a succession of 1 voltages that have been checked. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. There are a total of 16 pins on power management. Pin count of the power management is 16. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 4.75V. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. The mounting type of the supervisors is Surface MountThe temperature of the supervisors should be set to this range: 0°C~70°C TA. During operation, this power management system outputs Push-Pull, Push-Pull. It is always advisable to use MAX691, the base supervisor number, when searching for similar PMICs from the manufacturer. This power management requires 5V power to work.

MAX691CWE+ Features


Battery Backup Circuit type
Minimum supply voltage of 4.75V

MAX691CWE+ Applications


There are a lot of Maxim Integrated MAX691CWE+ Voltage Supervisors applications.

  • Data storage applications
  • Digitally controlled LDO regulators circuit
  • FPGA design
  • Embedded computing
  • Radar
  • Smart meter
  • DVR
  • Transformer load monitoring equipment
  • Microprocessor system
  • Consumer electronics

Write a review

Note: HTML is not translated!
    Bad           Good