MAX692ACPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | Through Hole |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Frequency | 250kHz |
| Base Part Number | MAX692 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Max Output Current | 20mA |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 200μA |
| Power Dissipation | 727mW |
| Max Supply Current | 350μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX692ACPA+ Overview
A total of 8 terminals are used to mount this power management. In terms of packaging, power management follows the Tube model. To assist you, this IC power includes 1 functions. There are 1 channels on this power managment ic that can be found in a series. There are 8-DIP (0.300, 7.62mm) functions included in this PMIC so that you can refer to them. With power management, you get a lot of benefits that you won't find in other Battery Backup Circuit products. There is a specification for the peak reflow temperature of the package to be 260. A supply voltage of 5V is used to conduct the PMIC chip. When 1 is applied to the power ic, it conducts. Through Hole mounts IC management. It is possible to subcategorize this power ic as a Power Management Circuits chip. It has a total of 8 pins that are attached to IC management. This power management has 8 pins. A voltage (Vsup) that doesn't fall below 1V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. Power management' mounting is recommended to be done with the Through Hole type of mounting. We recommend setting the supervisors to 0°C~70°C TA degrees. As this power managment ic operates, it is able to produce an output voltage of Push-Pull, Totem Pole. There is a supply current of 350μA for the power management. It is always advisable to use MAX692, the base supervisor number, when searching for similar PMICs from the manufacturer. To be able to work, this power management requires 5V volts of power. A maximum supply temperature of 350μA can be used with this power management. As a rule of thumb, voltage supervisor will work well in most cases with a frequency of 250kHz.
MAX692ACPA+ Features
Battery Backup Circuit type
Minimum supply voltage of 1V
350μA operating supply current
MAX692ACPA+ Applications
There are a lot of Maxim Integrated MAX692ACPA+ Voltage Supervisors applications.
- Radar
- DVR
- Electric heating appliances
- Automotive power systems
- Functional modules
- Display equipment
- Analog circuit
- Household appliances
- Automotive permanent magnet synchronous motors
- Power distribution systems of infant care room
